Stud size is minimum unless otherwise stated in design. For the most up-to-date information refer to the UL Fire resistance directory U · UL Type ULIX™ requires the use of insulation for single-layer, steel-framed UL fire-rated assemblies.
CGC Shaft Wall Systems are non-load-bearing gypsum wall partition assemblies constructed from outside the shaft at each floor. Shafts are enclosed early in construction, and the walls are CGC Shaft Wall Systems have been comprehensively tested for fire resistance ratings only CGC Steel C-H Stud (CH) CGC Shaft Wall Systems |
USG Cavity Shaft Wall Systems Catalog - SA
BXUV - Fire Resistance Ratings - ANSI/UL Certified for United States BXUV7 - Fire Resistance Ratings Design No. U September 27, Fire resistance assemblies and products are developed by the design submitter and have been investigated by UL for compliance with applicable requirements. The published information cannot always. Fire Rated System Design - UL U System F Print This Page. CAD · REVIT. UL U System F. Shaft Wall -Steel Stud (Non-load-bearing) Fire Rating. STC / Sound Test. 53 USG Stud size is minimum unless otherwise stated in design. For the most up-to-date information refer to the UL Fire resistance directory U · Follow USG on.
CAVITY SHAFTWALL SYSTEMS ALLOWABLE WALL HEIGHTS FOR 2-HOUR FIRE-RATED I-STUD ASSEMBLIES Stud Stud Min. Intermittent Air Pressure Load PSF Size Spacing Steel Allowable.
SHAFTWALL C-H STUD FIRE RATING ENGINEERING CATALOG C-H Studs & J-Track for Shaft Wall Construction are permitted system stud sizes under any UL certification. H 2 1/2" x 1 1/2" deep EU 30 H 4" x 1 1/2" deep EU 30 H 6" x 1 1/2" deep EU STEELER® INC. Shaft Walls. USG shaft wall systems are non-loadbearing gypsum wall partition – Underwriters Laboratories (UL)/Underwriters Laboratories Canada (ULC) Classified for fire resistance USG Steel C-H Stud (CH) 1" 7 USG Steel Jamb-Strut (JS) USG Steel E-Stud (ES) 2 4 Thickness–Steel Framinga Components Design Thicknessb Minimum Thickness.
Stor Svart Kuk Fucks Latin Hemmafru
ClarkDietrich Shaftwall Systems ClarkDietrich Building Systems provides fully tested and approved assemblies for shaftwall construction. What makes the ClarkDietrich system unique is that it has been tested with almost every gypsum board and shaft liner manufacturer in the country. Unlike competing systems, the ClarkDietrich CT Stud and J. Membrane Penetrations in Fire-Resistance Rated Walls Focus on protecting electrical boxes There are two types of penetrations to be considered. A through penetration has an opening that passes entirely through a fire-resistance rated assembly, while a for use in .
Assemblies Evaluated For 1. Non Axial Load Bearing Wall 2. Transverse Load Capacity 3. Fire Resistance 4. except where Z-Clips are used as in UL Design HW-D USG Contact: Manny Hurtado, Building Codes Manager Phone: Friction-fitted in "H" portion of CH studs. Gypsum Board Area Separation Wall Assemblies - Gypsum Board Assemblies - Plaster and Gypsum Board Assemblies (09 21 ) UL Design U - 1, 2, 3, or 4 Hour Wall Assembly Documents (1) Add to Package. Installation Instructions - UL Design U - .
Stud J-Track 1/2" ProRoc evaluated by Underwriters Laboratories Inc. and have been assigned UL Design U Additionally, the testing ProRoc® Shaftliner assemblies save money in several ways. With less weight per square foot than other shaft enclosures, structural framing. BXUV - Fire Resistance Ratings - ANSI/UL Certified for United States BXUV7 - Fire Resistance Ratings - CAN/ULC-S Certified for Canada. See General Information for Fire-resistance Ratings - ANSI/UL Certified for United States The max stud spacing of wall assemblies shall not exceed 24 in. OC (or 16 in. OC when Item 5b is used).